国产精品久久久久久亚洲伦理-亚洲国产成人久久精品91-亚洲精品国产a久久久久-久久夜色精品国产亚洲aⅴ

Hello, welcome to the official website of Wuhan Xinlaifu Hydraulic pneumatic Equipment Co. LTD
Hot keywords:

Rexroth hydraulic pump hydraulic pump station plunger pump hydraulic station system variable plunger pump

 

About us
News

Hydraulic station system, 1650 cold rolling mill hydraulic station system

Your position: Home page > Product center > Metallurgical hydraulic system of steel, cement, mine > Hydraulic station system, 1650 cold rolling mill hydraulic station system

Hydraulic station system, 1650 cold rolling mill hydraulic station system

Hydraulic station system, 1650 cold rolling mill hydraulic station system

Ddetailed information
Hydraulic station system, 1650 cold rolling mill hydraulic station system
■ Cold rolling mill
The cold rolling mill is a new type of steel bar cold rolling processing equipment. The machine can process hot-rolled wire rods and hot-rolled coils with a diameter between 6.5 mm and 12 mm into cold-rolled ribbed steel bars with a diameter of 5 mm to 12 mm. The cold-rolled ribbed steel bar rolled by the cold rolling mill is an updated product of cold-drawn low-carbon steel wire in the prestressed concrete structure. In the cast-in-situ concrete structure, it can be replaced with Grade I steel bar to save steel. It is a better kind of cold processed steel of the same kind. If speed adjustment is not required during the rolling process of the cold rolling mill, an AC motor can be used; if speed adjustment is required during the rolling process of the cold rolling mill, a DC motor can be used
■ Advantages
The cold rolling mill is a machine equipment that cold-drawn and cold-rolled the first-grade hot-rolled Q235 round steel into a spiral-shaped steel bar. The cold rolling mill equipment can simultaneously perform cold processing on the latitude and longitude directions of the base material during the process of rolling cold-rolled ribbed steel bars. Under the premise of retaining the relative balance and stability of the original cross-section center area, it can improve the resistance to position and compression. At the same time, it still retains sufficient elongation performance, so that the geometric parameters of [1] (flattening thickness, section width-to-thickness ratio, area reduction and pitch) and four material indicators (tensile strength, conditional yield value, elongation) Rate and cold bending) can be used in important industrial and civil buildings with safety levels, saving steel consumption and reducing construction prices
■ Structure
The cold rolling mill consists of a working mechanism and a transmission mechanism. among them:
① The working mechanism is composed of frame, roll, roll bearing, roll adjustment mechanism, guide device, rolling stand and other parts.
② The transmission mechanism is composed of gear frame, reducer, roller, coupling shaft, coupling and other parts. Rolling mill introduction
The gantry-type horizontal dual-active rolling mill consists of two active rolling mills. The installation method and structure of the two rolling mills are the same. The main transmission part adopts the structure of "motor → reducer → cardan shaft → rolling mill". The two rolling mills are horizontal rolling mills, and the rolls are installed horizontally. The rolling mill adopts a gantry type archway. The roll ring is sleeved on the roll main shaft and the nut is fixed. The two ends of the roll main shaft are equipped with bearing seats and installed in the middle of the gantry. The frame is coordinated to install, and the rolls are horizontally fixed in the middle of the gantry. The upper and lower rolls are installed in the same way. The one-pass reducing rolling mill flattens the raw material and extrudes the crescent-ribbed steel bars after passing through the two-pass forming rolling mill. The torsion guide adjusts the rolling piece to realize the elliptical rolling piece after one rolling is twisted 90° into the second-pass forming rolling mill. Produce finished steel bars.
Archway form: Longmen style
Transmission form: reducer transmission
Main motor power: 75KW∕2 sets;
Speed ??ratio of reducer: i=7.5
 
maintenance
①Check whether the electrical system of the cold rolling mill is normal before starting each shift;
②Check whether the oil level of each fuel tank is normal;
③Whether each oil injection part is filled with oil;
④Whether the base material feed is reasonable;
⑤After checking the above items;
⑥The electrical parts of the cold rolling mill should be cleaned up frequently;
⑦The moving parts should be checked frequently for loose and reasonable tightening.
⑧The cold rolling mill cannot be used beyond the limit during the production process to avoid damage to some mechanical parts of the cold rolling mill. It should be rolled according to the rolling standard to ensure the safe use of the cold rolling mill equipment and product qualification.
 
 
Products Show
■1650 cold rolling mill auxiliary pump station

1650冷軋機輔助泵站
 
■1650 cold rolling mill bending roll pumping station
1650冷軋機彎輥泵站
 
■1650 cold rolling mill presses on the pumping station
1650冷軋機壓上泵站
 

 

Product navigation

Home page  REXROTH  About Us  News Center  Download Center  Product Center  Site Map  XML Map

Wuhan Xinlaifu Hydraulic pneumatic Equipment Co. LTD

Tel: 027-85849187? Fax: 027-85849186? Pgone: 13971340391

Email: [email protected]? QQ:2909698088

Address: No. 28-30, Building 7, Hubei Modern Hardware & Electrical City, Dongxihu District, Wuhan

Factory address: Shenghua Industrial Park, Xincheng 12th Road, Dongxihu District, Wuhan

鄂ICP備16006620號6?

鄂公網安備 42010302001238號

You are the 1346745th visitor